Chameleon64 Series (not 64i) Serial Protocols Standard Routing B=Both Video and Audio V=Video Only A=Audio Only xx=Output yy=Input (If yy=00 then the output will be turned off) XXYYZZ=Mix Video and Audio: XX=Output, YY=Input Video, ZZ=Input Audio Examples: Bxxyy(Enter) xx=Output, yy=Input B1314(Enter) Audio and Video from Input 14 are routed to Output 13. V0806(Enter) Video from Input 06 is routed to Output 08 A1412(Enter) Audio from Input 12 is routed to Output 14 B011213(Enter) Video from Input 12 and Audio from Input 13 is routed to Output 01 To turn an output off, route from Input 00 B2400(Enter) turns output #24 off. Salvo Routing X=Salvo Both Video and Audio Y=Salvo Video Only Z=Salvo Audio Only mm=First Output in range nn=Last Output in range oo=Input number Examples: Xmmnnoo(Enter) or Ymmnnoo(Enter) or Zmmnnoo(Enter) X121508(Enter) Send Video and Audio from Input 08 to Outputs 12 through 15 Y010203(Enter) Send Video Only from Input 03 to Outputs 01 and 02 Z010516(Enter) Send Audio Only from Input 16 to Outputs 01-05 Batch Routing E=Both Video and Audio F=Video Only G=Audio Only EE=Take Examples: Exxyy(Enter) E1211(Enter)F1112(Enter)G1405(Enter)F0812(Enter)EE(Enter) As a batch do the following after receiving the EE command: Route Both Audio and Video from Input 11 to Output 12 [E1211] Route Video Only from Input 12 to Output 11 [F1112] Route Audio Only from Input 05 to Output 14 [G1405] Route Video Only from Input 12 to Output 08 [F0812] Execute [EE] Conference Mode (Cross Connect) J=Both Video and Audio K=Video Only L=Audio Only Examples: Jxxyy or Kxxyy, or Lxxyy J1215(Enter) Route Both Audio and Video from Input 15 to Output 12 and Input 12 to Output 15 K1215(Enter) Route Video Only from Input 15 to Output 12 and Input 12 to Output 15 L1215(Enter) Route Audio Only from Input 15 to Output 12 and Input 12 to Output 15 Timed Sequencer w/Front Panel Controller T=Start Sequence N=Stop Sequence nnn=1-999 Examples: Tnnn(Enter) or N(Enter) T135(Enter) will set the time interval to 135 seconds and begin cycling N(Enter) Stops the cycling System Status D= Crosspoint Map Each card will respond with a list of its outputs and the inputs connected to them. Interrogating for Active Cards I(Enter) Should respond 01_OK,02_OK etc. Store and Recall Power-Up Pattern As shipped from the factory, the Chameleon64 is programmed to connect all outputs to input 1 at power-up. To store a different power-up pattern, first set the chameleon64 to the pattern desired, then send the two-byte command S(Enter) S = Store Pattern R= Recall Pattern Examples: S(Enter) or R(Enter) Front Panel Control Settings Command Function Argument S80 Store pattern 01-20 S81 Recall pattern 01-20 S90 Timed mode on S91 Timed mode off S92 Timed mode interval 1-99 S93 Select router 1-4x4 2-8x8 3-16x16 4-Cham64 5-ChamHB S94 Clear patterns No=0 Yes=1 S95 Salvo Crosspoints S96 Display Current pattern Enter to continue S97 Interrogates for cards Cham64 only S98 Lock/unlock output 01-64 General Chameleon Serial Communications Requirements: 1:1 9-pin Serial (DB9) 9600 Baud 8-bit, No Parity, One or Two Stop Bits No Handshaking is required Pin 2 = Transmit Pin 3 = Receive Pin 5 = Ground