Chameleon256 HB/MBSeries Serial Protocols Standard Routing B=Both Video and Audio V=Video Only A=Audio Only Q=Routes both Audio and Video from different Inputs xxx=Output yyy=Input (If yyy=00 then the output will be turned off) Qxxxyyyzzz=Mix Video and Audio: XXX=Output, YYY=Input Video, ZZZ=Input Audio Examples: Bxxxyyy(Enter) xxx=Output, yyy=Input B123114(Enter) Audio and Video from Input 114 are routed to Output 123. V018016(Enter) Video from Input 016 is routed to Output 018 A114092(Enter) Audio from Input 092 is routed to Output 114 Q011112123(Enter) Video from Input 112 and Audio from Input 123 is routed to Output 011 To turn an output off, route from Input 000 B124000(Enter) turns output #124 off. Salvo Routing X=Salvo Both Video and Audio Y=Salvo Video Only Z=Salvo Audio Only mmm=First Output in range nnn=Last Output in range ooo=Input number Examples: Xmmmnnnooo(Enter) or Ymmmnnnooo(Enter) or Zmmmnnnooo(Enter) X082125038(Enter) Send Video and Audio from Input 038 to Outputs 082 through 125 Y082125038 (Enter) Send Video Only from Input 038 to Outputs 082 through 125 Z082125038 (Enter) Send Audio Only from Input 038 to Outputs 082 through 125 Batch (Queue) Routing E=Both Video and Audio F=Video Only G=Audio Only EE=Take xxx=Output yyy=Input Examples: Exxxyyy(Enter) E132131(Enter)F131132(Enter)G011035(Enter)F083132(Enter)EE(Enter) As a batch do the following after receiving the EE command: Route Both Audio and Video from Input 131 to Output 132 [E1211] Route Video Only from Input 132 to Output 131 [F1112] Route Audio Only from Input 035 to Output 011 [G1405] Route Video Only from Input 132 to Output 083 [F0812] Execute [EE] Conference Mode (Cross Connect) J=Both Video and Audio K=Video Only L=Audio Only xxx=Output yyy=Input Examples: Jxxxyyyy or Kxxxyyy, or Lxxxyyy J089021(Enter) Route Both Audio and Video from Input 021 to Output 089 and Input 089 to Output 021 K012015(Enter) Route Video Only from Input 015 to Output 012 and Input 012 to Output 015 L125132(Enter) Route Audio Only from Input 132 to Output 125 and Input 125 to Output 132 Timed Sequencer T=Start Sequence N=Stop Sequence nnn=001-999 Examples: Tnnn(Enter) or N(Enter) T135(Enter) will set the time interval to 135 seconds and begin cycling through 20 stored patterns N(Enter) Stops the cycling Interrogating a Crosspoint Condition D= Crosspoint condition xxx = First crosspoint displayed yyy = Last crosspoint displayed D0 = Display entire crosspoint map in condensed from M = Display entire crosspoint map Example: D003089(Enter) Displays status of crosspoints 003-089 D0(Enter) Displays the entire crosspoint map in condensed form M(Enter) Displays the entire crosspoint map Interrogating for Active Cards I(Enter) Initiates the signon message and revision level of software W(Enter) Displays active card: 01_OK, 02_OK,03_OK etc. Store and Recall Patterns S = Store Pattern R= Recall Pattern nn= Pattern # 01-20 Examples: S16(Enter) Stores current crosspoint pattern as #16 R11(Enter) Recalls pattern #11 Front Panel Control Settings Command Function Argument Store80 Store pattern 01-20 Store81 Recall pattern 01-20 Store82 Output number for 01-64 single station mode Store83 Set Mode 1=Full Function 2=Single Station 3=Strings 4=Recall Store90 Timed mode on Store91 Timed mode off Store92 Timed mode interval 1-999 Store93 Select router 5-Chameleon HB/256 Store94 Clear patterns No=0 Yes=1 Store95 Salvo Mode on/off Store96 Display Current pattern Enter to continue Store97 Interrogates for cards Chameleons only Store98 Lock/unlock output 01-256 Store99 Queue mode on/off Mode 1=Full Function 2=Single Station 3=Strings 4=Recall Patterns General Chameleon Serial Communications Requirements: 1:1 9-pin Serial (DB9) 9600 Baud (factory setting) 8-bit, No Parity, One or Two Stop Bits No Handshaking is required Pin 2 = Transmit Pin 3 = Receive Pin 5 = Ground